A pink spot on sanded Slick Sand Optex is a reason to stop before sealer. Evercoat puts a pink sanding guide into this polyester primer surfacer. Remove all remaining pink color and residue as directed before you apply another coating or polyester filler. You do not need to strip the sound surfacer just because a low spot needs attention.
If you first notice the pink after spraying white, you have a different question. The color may be showing through because coverage is incomplete, or it may be a stain from a lower layer. Work out where it comes from before adding clear.
Read the Pink Areas on the Sanded Panel
|
What you see |
What to check |
What to do next |
|
A small pink strip along a body line |
Whether that shape was reached during sanding |
Use a method that fits the contour and preserves the edge. |
|
Pink stays in the middle as the surrounding primer sands away |
Whether the spot is lower than the surrounding surface |
Check the shape. Correct an actual low spot rather than sanding the whole area down to it. |
|
Primer thins or another layer shows while pink still remains nearby |
Whether you have enough sound material to level the area |
Stop and restore the exposed or uneven area under the approved repair procedure. |
|
Pink cast under white basecoat |
Undercoat shade, coverage and possible staining |
Pause before clear. Compare with a test card and trace the difference to the right layer. |
Read the label before you interpret the color. A pink sanding guide in Slick Sand Optex serves a different purpose from a pigment in a conventional primer or a color-change indicator in a filler. The sanding instructions for this product do not apply to every pink material.
Sand Slick Sand Optex at the Right Stage
Start with the current Evercoat Slick Sand Optex data sheet for the material and region you are using. The July 2025 U.S. sheet gives these reference values.
|
Check on this product |
Published reference |
|
Ready to sand at 70–72°F (21–22°C) |
About 2 hours, depending on film build |
|
Dry sanding before topcoating |
180–400 grit. Also verify the surface requirements of the next coating. |
|
Fluid nozzle for applying the surfacer |
2.0 mm or larger |
Do not judge readiness by surface feel alone. When it is ready, use a block that suits the panel shape. Read the areas it reaches and the ones it misses. Stop if the edges are thinning before the center levels. If the panel needs more work, remove the remaining pink as required before adding another product and restore the shape using the approved system. Follow the guide to repairing a sanding burn through if the abrasive exposes a different substrate. For a different surfacer, check its own instructions and review high build primer application problems.
Check the Undercoat Before Spraying White
Clear away sanding residue using the approved method. Look at the clean panel from a low angle to check the surface shape, then look straight at it for scratches, pores and remaining color. The absence of pink does not by itself mean that the final scratch pattern or substrate is ready. See paint prep before basecoat for those checks.
Use the paint system's specified undercoat shade for the white. On a test card, set up the same undercoat and basecoat, then check coverage at the specified inspection stage. If the color is still uneven on the vehicle, check coverage and the lower layers before deciding on a correction. Do not put clear over a pink shadow and expect it to disappear.
Choose the Gun for the Next Coat
Sealer can give you a uniform base where the system permits it. Use it after the surface is sound and the pink is fully gone. It cannot fix a low area or remove the guide color underneath.
The PORPHIS PC-415 MP is available in 1.3 mm and 1.8 mm. It can be evaluated for the next sealer or primer only when that coating's instructions accept the chosen setup. Neither PC-415 nozzle meets Evercoat's size requirement for applying Slick Sand Optex itself. Pick the gun for the actual material, not for the name of the step.
Questions About Pink Primer
Can I seal over a faint pink area
Not with Slick Sand Optex. Evercoat requires the pink to be removed before another coating. If the mark lies in a low spot, address the contour so you can meet that requirement without thinning the surrounding repair.
Will pink primer bleed through white paint
A pink appearance under white does not identify the cause. Check the approved undercoat shade, how well the basecoat hides it and whether the color is migrating from a lower layer. Correct the affected layer before clear.
Can a 1.8 mm setup spray this Optex surfacer
It is below the listed minimum of 2.0 mm for this product. Check the exact material's data sheet and choose the required nozzle. The PC-415's 1.8 mm option may suit a different surfacer whose instructions allow it.

Compartilhar:
Can You Spray 2K Paint Over Rattle Can Paint
Body Filler Showing Through Primer and How to Fix It